Problemen met uw microSD-kaart oplossen: fouten met de 'read-only'-lock en de 'multi-volume-set'-instelling

This guide addresses a common issue reported by customers after receiving their Brick Pro device: the bundled microSD card appears locked to read-only mode and triggers a misleading “multi-volume set” error when accessed through a standard SD card reader on a Windows computer. Below, we outline the likely causes of this behaviour and provide a step-by-step resolution process.

Reported Case #

“My Brick Pro arrived safe and sound (thank you for the quick dispatch). However, I wanted to put some additional content onto the MicroSD card. When connecting it to the computer via a SD adapter+reader I get an error saying ‘please insert the last disk of the multi-volume set and click ok to continue’ additionally the card is locked to read only (DiskPart/RegEdit is unable to change this), preventing my adding files to the disk.”

This is a known, resolvable issue and does not necessarily indicate a defective card. It typically arises from how the file system and partition metadata were written to the card prior to shipping, which can cause Windows to misinterpret the volume structure.

Understanding the Symptoms #

  • “Please insert the last disk of the multi-volume set” error: This message is generated by Windows Explorer when it detects partition or file system metadata that resembles a segmented archive or a multi-partition disk image, rather than a standard single-volume card.
  • Read-only lock that persists through DiskPart and the Registry Editor: This indicates the restriction is not a simple software flag but is instead tied to the underlying file system state or partition table, which standard Windows tools cannot override without reformatting.
  • Hardware eliminated as a cause: Since the issue persists across two separate adapters and a card reader confirmed to work correctly with other cards, the SD adapter and reader can be ruled out as the source of the problem.

Likely Root Causes #

The combination of symptoms described above is consistent with one or more of the following:

  • Non-standard partition layout: The card may contain a partition table or file system (such as an exFAT of ext4 partition) created by imaging software that Windows does not fully support, causing Explorer to misread the volume boundaries.
  • Residual disk image signatures: Cards prepared using disk-imaging tools can retain metadata that identifies the card as part of a “multi-volume” archive, even though only a single physical card is present.
  • File system flagged as read-only at the partition level: Certain file systems include an internal read-only attribute set during image creation to prevent accidental modification of factory content. This attribute is independent of the physical write-protect notch on an SD adapter.

Step-by-Step Resolution #

Step 1: Back Up Existing Content #

Before making any changes, copy any files you wish to retain from the microSD card to your computer. If the card is currently read-only, standard copy operations should still succeed, since reading is unaffected by the write restriction.

Step 2: Inspect the Disk in Disk Management #

  1. Pers Windows + X and select Disk Management.
  2. Locate the microSD card in the list of disks. Note the number and size of partitions shown.
  3. If you see multiple partitions, an unrecognised partition type, or “RAW” listed as the file system, this confirms a non-standard layout is the cause of the Explorer error.

Step 3: Clear the Disk Using DiskPart #

If Step 2 confirms a non-standard or multi-partition layout, use DiskPart to remove all existing partition data and reset the disk to a clean state.

diskpart
list disk
select disk X        (replace X with the number corresponding to your microSD card)
attributes disk clear readonly
clean
create partition primary
format fs=exfat quick
assign
exit

Caution: Confirm the correct disk number before running clean. This command permanently erases all data on the selected disk. Selecting the wrong disk may result in irreversible data loss on another drive.

The attributes disk clear readonly command specifically targets the read-only flag that persists independently of adapter locks and cannot be cleared through the Registry Editor alone.

Step 4: Reformat Using a Dedicated SD Tool #

If DiskPart reports that it cannot clear the read-only attribute or clean the disk, use the official SD Memory Card Formatter tool provided by the SD Association. This utility is designed to correctly reset cards that have been initialised with non-Windows-native file systems or partition structures.

  1. Download and install the SD Card Formatter tool.
  2. Insert the microSD card via your adapter and reader.
  3. Select the corresponding drive letter within the tool.
  4. Choose Quick Format of Full Format (Overwrite) if a quick format does not resolve the issue.
  5. Confirm and begin the format process.

Step 5: Verify the Card #

Once formatting completes, eject the card safely, reinsert it, and confirm that:

  • The card is recognised with a single partition and standard file system (typically exFAT of FAT32).
  • Files can be copied to and deleted from the card without a read-only warning.
  • The “multi-volume set” error no longer appears when the card is accessed.

Reference: Common Symptoms and Fixes #

SymptomLikely CauseRecommended Fix
“Insert the last disk of the multi-volume set” errorResidual partition or image metadata misread by Windows ExplorerClean and reformat via DiskPart or SD Card Formatter
Read-only lock not cleared by DiskPart or Registry editsFile system-level read-only attribute set during card preparationRun attributes disk clear readonly before formatting
Card shows as RAW or unrecognised file systemNon-Windows-native file system present on the cardFull format using the SD Card Formatter tool
Adapter or reader suspected as faultyUsually not the cause if other cards work normallyConfirm with a second card; if other cards work, focus on the card itself

Preventing Recurrence #

  • Always use Safely Remove Hardware (or your operating system’s equivalent) before disconnecting the microSD card from any device.
  • When copying files from a computer back onto the card, use a single, standard file system such as exFAT or FAT32 rather than creating additional partitions.
  • Avoid using disk-imaging utilities not specifically designed for SD card preparation, as these can leave behind metadata that is incompatible with standard operating system tools.

When to Contact Support #

If you have completed the steps above and the card still cannot be reformatted, continues to report a read-only state, or is not recognised at all in Disk Management, the card itself may be faulty at the hardware level. In this case, please contact our support team with the following information so we can arrange a replacement:

  • The exact error message displayed, including a screenshot if possible.
  • The output of list disk en list partition from DiskPart.
  • Confirmation of the operating system and card reader used.
  • Your order number and the date your Brick Pro was received.
Wat zijn je gevoelens?
Bijgewerkt op 11 november 2026
0